1 |
# /etc/conf.d/net.eth0 - example eth0 network device configuration |
# /etc/conf.d/net.eth0 - example eth0 network device configuration |
2 |
# $Header: /home/cvsd/magellan-cvs/magellan-src/magellan-initscripts/etc/conf.d/net.sample,v 1.2 2007-12-13 12:05:38 niro Exp $ |
# $Id$ |
3 |
|
|
4 |
# Enable this device automatically on system boot. |
# Enable this device automatically on system boot. |
5 |
# If set to anything but ?yes? the NIC will be ignored by |
# If set to anything but ?yes? the NIC will be ignored by |
84 |
#WIRELESS_KEY |
#WIRELESS_KEY |
85 |
# Encryption key in ascii (or use hex key, for WEP+WPA) |
# Encryption key in ascii (or use hex key, for WEP+WPA) |
86 |
#WIRELESS_KEY_ASCII |
#WIRELESS_KEY_ASCII |
87 |
# driver used for wpa_supplicant |
# driver used for wpa_supplicant (scripts defaults to wext) |
88 |
|
# to see all possible drivers, run 'wpa_supplicant --help' |
89 |
#WIRELESS_WPA_DRIVER=wext |
#WIRELESS_WPA_DRIVER=wext |
90 |
|
|
91 |
|
|
95 |
# Note: to setup a bridge this file must be called net.br[0-9] |
# Note: to setup a bridge this file must be called net.br[0-9] |
96 |
# |
# |
97 |
# Interfaces to which the bridge shall point to |
# Interfaces to which the bridge shall point to |
98 |
# It is possible to give more then on |
# It is possible to use more than one |
99 |
#BRIDGE_INTERFACES="eth0 eth1" |
#BRIDGE_INTERFACES="eth0 eth1" |
100 |
# Enables or disables Spanning Tree |
# Enables or disables Spanning Tree |
101 |
# Possible values are 'on' and 'off' |
# Possible values are 'on' and 'off' |
102 |
#BRIDGE_STP="on" |
#BRIDGE_STP="on" |
103 |
|
# Sets ageing time |
104 |
|
#BRIDGE_AGEING_TIME |
105 |
|
# Sets bridge priority |
106 |
|
#BRIDGE_PRIORITY |
107 |
|
# Sets bridge forwarde delay time |
108 |
|
#BRIDGE_FORWARD_DELAY |
109 |
|
# Sets hello time |
110 |
|
#BRIDGE_HELLO_TIME |
111 |
|
# Sets max message age |
112 |
|
#BRIDGE_MAX_MESSAGE_AGE |
113 |
|
# Sets path cost for a configured bridge port/interface |
114 |
|
# It is possible to use more than one |
115 |
|
# e.g. port1=cost1 port2=cost2 |
116 |
|
#BRIDGE_PATH_COST="eth0=12 eth2=9" |
117 |
|
# Sets port priority for a configured bridge port/interface |
118 |
|
# It is possible to use more than one |
119 |
|
# e.g. port1=prio1 port2=prio2 |
120 |
|
#BRIDGE_PORT_PRIORITY="eth0=1 eth2=3" |
121 |
# |
# |
122 |
# Here comes the same settings like with normal NICs |
# Networking for the bridge can be configured as normal |
123 |
# A static example: |
# A static example: |
124 |
#NETWORKING="static" |
#NETWORKING="static" |
125 |
#IP="192.168.0.1" |
#IP="192.168.0.1" |