Magellan Linux

  • Back to homepage
    • /[magellan-source]/trunk/initscripts/sysvinit/conf.d/net.sample

    Diff of /trunk/initscripts/sysvinit/conf.d/net.sample

    Parent Directory Parent Directory | Revision Log Revision Log | View Patch Patch

    revision 867 by niro, Sat May 9 16:08:38 2009 UTC revision 1092 by niro, Wed Jul 14 11:02:11 2010 UTC
    # Line 1  Line 1 
    1  # /etc/conf.d/net.eth0 - example eth0 network device configuration  # /etc/conf.d/net.eth0 - example eth0 network device configuration
    2  # $Header: /home/cvsd/magellan-cvs/magellan-src/magellan-initscripts/etc/conf.d/net.sample,v 1.2 2007-12-13 12:05:38 niro Exp $  # $Id$
    3    
    4  # Enable this device automatically on system boot.  # Enable this device automatically on system boot.
    5  # If set to anything but ?yes? the NIC will be ignored by  # If set to anything but ?yes? the NIC will be ignored by
    # Line 84  DHCP_STOP="-k" Line 84  DHCP_STOP="-k"
    84  #WIRELESS_KEY  #WIRELESS_KEY
    85  # Encryption key in ascii (or use hex key, for WEP+WPA)  # Encryption key in ascii (or use hex key, for WEP+WPA)
    86  #WIRELESS_KEY_ASCII  #WIRELESS_KEY_ASCII
    87  # driver used for wpa_supplicant  # driver used for wpa_supplicant (scripts defaults to wext)
    88    # to see all possible drivers, run 'wpa_supplicant --help'
    89  #WIRELESS_WPA_DRIVER=wext  #WIRELESS_WPA_DRIVER=wext
    90    
    91    
    # Line 94  DHCP_STOP="-k" Line 95  DHCP_STOP="-k"
    95  # Note: to setup a bridge this file must be called net.br[0-9]  # Note: to setup a bridge this file must be called net.br[0-9]
    96  #  #
    97  # Interfaces to which the bridge shall point to  # Interfaces to which the bridge shall point to
    98  # It is possible to give more then on  # It is possible to use more than one
    99  #BRIDGE_INTERFACES="eth0 eth1"  #BRIDGE_INTERFACES="eth0 eth1"
    100  # Enables or disables Spanning Tree  # Enables or disables Spanning Tree
    101  # Possible values are 'on' and 'off'  # Possible values are 'on' and 'off'
    102  #BRIDGE_STP="on"  #BRIDGE_STP="on"
    103    # Sets ageing time
    104    #BRIDGE_AGEING_TIME
    105    # Sets bridge priority
    106    #BRIDGE_PRIORITY
    107    # Sets bridge forwarde delay time
    108    #BRIDGE_FORWARD_DELAY
    109    # Sets hello time
    110    #BRIDGE_HELLO_TIME
    111    # Sets max message age
    112    #BRIDGE_MAX_MESSAGE_AGE
    113    # Sets path cost for a configured bridge port/interface
    114    # It is possible to use more than one
    115    # e.g. port1=cost1 port2=cost2
    116    #BRIDGE_PATH_COST="eth0=12 eth2=9"
    117    # Sets port priority for a configured bridge port/interface
    118    # It is possible to use more than one
    119    # e.g. port1=prio1 port2=prio2
    120    #BRIDGE_PORT_PRIORITY="eth0=1 eth2=3"
    121  #  #
    122  # Here comes the same settings like with normal NICs  # Networking for the bridge can be configured as normal
    123  # A static example:  # A static example:
    124  #NETWORKING="static"  #NETWORKING="static"
    125  #IP="192.168.0.1"  #IP="192.168.0.1"
    Legend:
    Removed from v.867  
    changed lines
      Added in v.1092