etc/conf.d/net.eth0

# /etc/conf.d/net.eth0 - example eth0 network device configuration
# $Header: /home/cvsd/magellan-cvs/magellan-src/magellan-initscripts/etc/conf.d/net.eth0,v 1.4 2005-07-02 20:38:57 niro Exp $

# Enable this device automatically on system boot.
# If set to anything but ?yes? the NIC will be ignored by
# the network script and not be brought up.
ONBOOT="yes"


# Static networking configuration example:
# This method may be used to define ethernet interfaces with
# statically allocated IPv4 addresses.

# NETWORKING defines which method is used [static|dhcp].
#NETWORKING="static"

# IP is required to set the address of the interface.
#IP="192.168.0.1"

# Requiered to configure the netmask.
#NETMASK="255.255.255.0"

# Required to configure the broadcast address.
#BROADCAST="192.168.0.255"


# Dynamic networking configuration example:
# This method may be used to obtain an address via DHCP.

# Enables the dhcp networking method.
NETWORKING="dhcp"

# Which dhcp client do you want to use ?
DHCP_PROG="/sbin/dhcpcd"

# DHCP_START allows you to pass additional
# startup parameters to your dhcp client.
# Ex: Timeout after 10 seconds
DHCP_START="-t 10"

# DHCP_STOP allows you to pass additional
# stop parameters to your dhcp client.
# Ex: -k kills the dhcp-cache at system shutdown
#     -z will not; keeps the resolv.conf etc.
DHCP_STOP="-z"


# The GATEWAY variable should contain the default gateway IP address,
# if one is present. If not, then comment out the variables entirely.
# GATEWAY_IF defines the interface to bind the default gateway to.
#GATEWAY="192.168.0.100"
#GATEWAY_IF="eth0"
1	niro	133	# /etc/conf.d/net.eth0 - example eth0 network device configuration
2			# $Header: /home/cvsd/magellan-cvs/magellan-src/magellan-initscripts/etc/conf.d/net.eth0,v 1.4 2005-07-02 20:38:57 niro Exp $
3	niro	2
4	niro	133	# Enable this device automatically on system boot.
5			# If set to anything but ?yes? the NIC will be ignored by
6			# the network script and not be brought up.
7	niro	2	ONBOOT="yes"
8
9	niro	133
10
11
12			# Static networking configuration example:
13			# This method may be used to define ethernet interfaces with
14			# statically allocated IPv4 addresses.
15
16			# NETWORKING defines which method is used [static\|dhcp].
17	niro	2	#NETWORKING="static"
18	niro	133
19			# IP is required to set the address of the interface.
20	niro	2	#IP="192.168.0.1"
21	niro	133
22			# Requiered to configure the netmask.
23	niro	2	#NETMASK="255.255.255.0"
24	niro	133
25			# Required to configure the broadcast address.
26	niro	2	#BROADCAST="192.168.0.255"
27
28	niro	133
29
30
31			# Dynamic networking configuration example:
32			# This method may be used to obtain an address via DHCP.
33
34			# Enables the dhcp networking method.
35	niro	2	NETWORKING="dhcp"
36	niro	133
37			# Which dhcp client do you want to use ?
38	niro	2	DHCP_PROG="/sbin/dhcpcd"
39	niro	133
40			# DHCP_START allows you to pass additional
41			# startup parameters to your dhcp client.
42			# Ex: Timeout after 10 seconds
43	niro	19	DHCP_START="-t 10"
44	niro	133
45			# DHCP_STOP allows you to pass additional
46			# stop parameters to your dhcp client.
47			# Ex: -k kills the dhcp-cache at system shutdown
48			# -z will not; keeps the resolv.conf etc.
49	niro	2	DHCP_STOP="-z"
50
51	niro	133
52
53
54			# The GATEWAY variable should contain the default gateway IP address,
55			# if one is present. If not, then comment out the variables entirely.
56			# GATEWAY_IF defines the interface to bind the default gateway to.
57	niro	2	#GATEWAY="192.168.0.100"
58			#GATEWAY_IF="eth0"