etc/conf.d/net.eth0

# /etc/conf.d/net.eth0 - example eth0 network device configuration
# $Header: /home/cvsd/magellan-cvs/magellan-src/magellan-initscripts/etc/conf.d/net.eth0,v 1.11 2007-07-21 19:31:29 niro Exp $

# Enable this device automatically on system boot.
# If set to anything but ?yes? the NIC will be ignored by
# the network script and not be brought up.
ONBOOT="yes"


# Static networking configuration example:
# This method may be used to define ethernet interfaces with
# statically allocated IPv4 addresses.

# NETWORKING defines which method is used [static|dhcp].
#NETWORKING="static"

# IP is required to set the address of the interface.
#IP="192.168.0.1"

# Requiered to configure the netmask.
#NETMASK="255.255.255.0"

# Required to configure the broadcast address.
#BROADCAST="192.168.0.255"


# Dynamic networking configuration example:
# This method may be used to obtain an address via DHCP.

# Enables the dhcp networking method.
NETWORKING="dhcp"

# Which dhcp client do you want to use ?
DHCP_PROG="/sbin/dhcpcd"

# DHCP_START allows you to pass additional
# startup parameters to your dhcp client.
# Ex: Timeout after 10 seconds
DHCP_START="-t 10"

# DHCP_STOP allows you to pass additional
# stop parameters to your dhcp client.
# Ex: -k kills the dhcp-cache at system shutdown
#     -z will not; keeps the resolv.conf etc.
DHCP_STOP="-k"


# The GATEWAY variable should contain the default gateway IP address,
# if one is present. If not, then comment out the variables entirely.
#GATEWAY="192.168.0.100"


# The NAMESERVER variable should contain a list of DNS-servers,
# if there are some present. This also overrides the DHCP-settings.
#NAMESERVER="192.168.0.100 192.168.0.101"


#
# Wireless networking extensions (see man iwconfig(8) for more details)
#
# transfer rate 11M, 54M
#WIRELESS_BITRATE
# which channel shall be used [1-14] (use this or frequency)
#WIRELESS_CHANNEL
# network SSID
#WIRELESS_ESSID
# wich freqency shall be used
#WIRELESS_FREQUENCY
# wireless operation mode (managed=infrastrukte, ad-hoc, master=ap)
#WIRELESS_MODE
# nickname of the wireless node
#WIRELESS_NICK
# which authentification mode shall be used (wep,wpa,off)
#WIRELESS_AUTH_MODE
# Encryption key length, 64=WEP64, 128=WEP128, 256=WEP256
#WIRELESS_KEY_LENGTH
# Encryption key in hex (or use ascii key)
#WIRELESS_KEY
# Encryption key in ascii (or use hex key)
#WIRELESS_KEY_ASCII
# driver used for wpa_supplicant
# WIRELESS_WPA_DRIVER=zydas


#
# Setup Bridges
#
# Note: to setup a bridge this file must be called net.br[0-9]
#
# Interface to which the bridge shall point to
#BRIDGE_INTERFACE="eth0"
# Here comes the same settings like with normal NICs
# A static example:
#NETWORKING="static"
#IP="192.168.0.1"
#NETMASK="255.255.255.0"
#BROADCAST="192.168.0.255"
1	niro	133	# /etc/conf.d/net.eth0 - example eth0 network device configuration
2	niro	507	# $Header: /home/cvsd/magellan-cvs/magellan-src/magellan-initscripts/etc/conf.d/net.eth0,v 1.11 2007-07-21 19:31:29 niro Exp $
3	niro	2
4	niro	133	# Enable this device automatically on system boot.
5			# If set to anything but ?yes? the NIC will be ignored by
6			# the network script and not be brought up.
7	niro	2	ONBOOT="yes"
8
9	niro	133
10
11
12			# Static networking configuration example:
13			# This method may be used to define ethernet interfaces with
14			# statically allocated IPv4 addresses.
15
16			# NETWORKING defines which method is used [static\|dhcp].
17	niro	2	#NETWORKING="static"
18	niro	133
19			# IP is required to set the address of the interface.
20	niro	2	#IP="192.168.0.1"
21	niro	133
22			# Requiered to configure the netmask.
23	niro	2	#NETMASK="255.255.255.0"
24	niro	133
25			# Required to configure the broadcast address.
26	niro	2	#BROADCAST="192.168.0.255"
27
28	niro	133
29
30
31			# Dynamic networking configuration example:
32			# This method may be used to obtain an address via DHCP.
33
34			# Enables the dhcp networking method.
35	niro	2	NETWORKING="dhcp"
36	niro	133
37			# Which dhcp client do you want to use ?
38	niro	2	DHCP_PROG="/sbin/dhcpcd"
39	niro	133
40			# DHCP_START allows you to pass additional
41			# startup parameters to your dhcp client.
42			# Ex: Timeout after 10 seconds
43	niro	19	DHCP_START="-t 10"
44	niro	133
45			# DHCP_STOP allows you to pass additional
46			# stop parameters to your dhcp client.
47			# Ex: -k kills the dhcp-cache at system shutdown
48			# -z will not; keeps the resolv.conf etc.
49	niro	392	DHCP_STOP="-k"
50	niro	2
51	niro	133
52
53
54			# The GATEWAY variable should contain the default gateway IP address,
55			# if one is present. If not, then comment out the variables entirely.
56	niro	2	#GATEWAY="192.168.0.100"
57	niro	244
58
59	niro	245	# The NAMESERVER variable should contain a list of DNS-servers,
60			# if there are some present. This also overrides the DHCP-settings.
61			#NAMESERVER="192.168.0.100 192.168.0.101"
62
63
64	niro	244	#
65			# Wireless networking extensions (see man iwconfig(8) for more details)
66			#
67			# transfer rate 11M, 54M
68			#WIRELESS_BITRATE
69			# which channel shall be used [1-14] (use this or frequency)
70			#WIRELESS_CHANNEL
71			# network SSID
72			#WIRELESS_ESSID
73			# wich freqency shall be used
74			#WIRELESS_FREQUENCY
75	niro	426	# wireless operation mode (managed=infrastrukte, ad-hoc, master=ap)
76	niro	244	#WIRELESS_MODE
77			# nickname of the wireless node
78			#WIRELESS_NICK
79	niro	388	# which authentification mode shall be used (wep,wpa,off)
80	niro	244	#WIRELESS_AUTH_MODE
81			# Encryption key length, 64=WEP64, 128=WEP128, 256=WEP256
82			#WIRELESS_KEY_LENGTH
83			# Encryption key in hex (or use ascii key)
84			#WIRELESS_KEY
85			# Encryption key in ascii (or use hex key)
86			#WIRELESS_KEY_ASCII
87	niro	426	# driver used for wpa_supplicant
88	niro	267	# WIRELESS_WPA_DRIVER=zydas
89	niro	507
90
91			#
92			# Setup Bridges
93			#
94			# Note: to setup a bridge this file must be called net.br[0-9]
95			#
96			# Interface to which the bridge shall point to
97			#BRIDGE_INTERFACE="eth0"
98			# Here comes the same settings like with normal NICs
99			# A static example:
100			#NETWORKING="static"
101			#IP="192.168.0.1"
102			#NETMASK="255.255.255.0"
103			#BROADCAST="192.168.0.255"