| 1 |
#sets up the eth0 device |
# /etc/conf.d/net.eth0 - example eth0 network device configuration |
| 2 |
|
# $Header: /home/cvsd/magellan-cvs/magellan-src/magellan-initscripts/etc/conf.d/net.eth0,v 1.6 2005-09-22 22:15:20 niro Exp $ |
| 3 |
|
|
| 4 |
#loads the device at boot |
# Enable this device automatically on system boot. |
| 5 |
|
# If set to anything but ?yes? the NIC will be ignored by |
| 6 |
|
# the network script and not be brought up. |
| 7 |
ONBOOT="yes" |
ONBOOT="yes" |
| 8 |
|
|
| 9 |
#sets static networking |
|
| 10 |
|
|
| 11 |
|
|
| 12 |
|
# Static networking configuration example: |
| 13 |
|
# This method may be used to define ethernet interfaces with |
| 14 |
|
# statically allocated IPv4 addresses. |
| 15 |
|
|
| 16 |
|
# NETWORKING defines which method is used [static|dhcp]. |
| 17 |
#NETWORKING="static" |
#NETWORKING="static" |
| 18 |
|
|
| 19 |
|
# IP is required to set the address of the interface. |
| 20 |
#IP="192.168.0.1" |
#IP="192.168.0.1" |
| 21 |
|
|
| 22 |
|
# Requiered to configure the netmask. |
| 23 |
#NETMASK="255.255.255.0" |
#NETMASK="255.255.255.0" |
| 24 |
|
|
| 25 |
|
# Required to configure the broadcast address. |
| 26 |
#BROADCAST="192.168.0.255" |
#BROADCAST="192.168.0.255" |
| 27 |
|
|
| 28 |
#sets dhcp networking |
|
| 29 |
|
|
| 30 |
|
|
| 31 |
|
# Dynamic networking configuration example: |
| 32 |
|
# This method may be used to obtain an address via DHCP. |
| 33 |
|
|
| 34 |
|
# Enables the dhcp networking method. |
| 35 |
NETWORKING="dhcp" |
NETWORKING="dhcp" |
| 36 |
|
|
| 37 |
|
# Which dhcp client do you want to use ? |
| 38 |
DHCP_PROG="/sbin/dhcpcd" |
DHCP_PROG="/sbin/dhcpcd" |
| 39 |
#timeout after 10 seconds |
|
| 40 |
|
# DHCP_START allows you to pass additional |
| 41 |
|
# startup parameters to your dhcp client. |
| 42 |
|
# Ex: Timeout after 10 seconds |
| 43 |
DHCP_START="-t 10" |
DHCP_START="-t 10" |
| 44 |
# -k kills the dhcp-cache at system shutdown |
|
| 45 |
# -z will not |
# DHCP_STOP allows you to pass additional |
| 46 |
|
# stop parameters to your dhcp client. |
| 47 |
|
# Ex: -k kills the dhcp-cache at system shutdown |
| 48 |
|
# -z will not; keeps the resolv.conf etc. |
| 49 |
DHCP_STOP="-z" |
DHCP_STOP="-z" |
| 50 |
|
|
| 51 |
#Default Gateway Options |
|
| 52 |
|
|
| 53 |
|
|
| 54 |
|
# The GATEWAY variable should contain the default gateway IP address, |
| 55 |
|
# if one is present. If not, then comment out the variables entirely. |
| 56 |
#GATEWAY="192.168.0.100" |
#GATEWAY="192.168.0.100" |
| 57 |
#GATEWAY_IF="eth0" |
|
| 58 |
|
|
| 59 |
|
# The NAMESERVER variable should contain a list of DNS-servers, |
| 60 |
|
# if there are some present. This also overrides the DHCP-settings. |
| 61 |
|
#NAMESERVER="192.168.0.100 192.168.0.101" |
| 62 |
|
|
| 63 |
|
|
| 64 |
|
# |
| 65 |
|
# Wireless networking extensions (see man iwconfig(8) for more details) |
| 66 |
|
# |
| 67 |
|
# transfer rate 11M, 54M |
| 68 |
|
#WIRELESS_BITRATE |
| 69 |
|
# which channel shall be used [1-14] (use this or frequency) |
| 70 |
|
#WIRELESS_CHANNEL |
| 71 |
|
# network SSID |
| 72 |
|
#WIRELESS_ESSID |
| 73 |
|
# wich freqency shall be used |
| 74 |
|
#WIRELESS_FREQUENCY |
| 75 |
|
# wireless operation mode (managed=infrastrukte, ad-hc, master=ap) |
| 76 |
|
#WIRELESS_MODE |
| 77 |
|
# nickname of the wireless node |
| 78 |
|
#WIRELESS_NICK |
| 79 |
|
# which authentification mode shall be used (open, restricted, off) |
| 80 |
|
#WIRELESS_AUTH_MODE |
| 81 |
|
# Encryption key length, 64=WEP64, 128=WEP128, 256=WEP256 |
| 82 |
|
#WIRELESS_KEY_LENGTH |
| 83 |
|
# Encryption key in hex (or use ascii key) |
| 84 |
|
#WIRELESS_KEY |
| 85 |
|
# Encryption key in ascii (or use hex key) |
| 86 |
|
#WIRELESS_KEY_ASCII |
Parent Directory
| 
Revision Log
| 
Patch