Contents of /trunk/magellan-initscripts/etc/conf.d/net.eth0
Parent Directory | Revision Log
Revision 507 -
(show annotations)
(download)
Sat Jul 21 19:31:29 2007 UTC (17 years, 2 months ago) by niro
File size: 2773 byte(s)
Sat Jul 21 19:31:29 2007 UTC (17 years, 2 months ago) by niro
File size: 2773 byte(s)
-added support for bridges
1 | # /etc/conf.d/net.eth0 - example eth0 network device configuration |
2 | # $Header: /home/cvsd/magellan-cvs/magellan-src/magellan-initscripts/etc/conf.d/net.eth0,v 1.11 2007-07-21 19:31:29 niro Exp $ |
3 | |
4 | # Enable this device automatically on system boot. |
5 | # If set to anything but ?yes? the NIC will be ignored by |
6 | # the network script and not be brought up. |
7 | ONBOOT="yes" |
8 | |
9 | |
10 | |
11 | |
12 | # Static networking configuration example: |
13 | # This method may be used to define ethernet interfaces with |
14 | # statically allocated IPv4 addresses. |
15 | |
16 | # NETWORKING defines which method is used [static|dhcp]. |
17 | #NETWORKING="static" |
18 | |
19 | # IP is required to set the address of the interface. |
20 | #IP="192.168.0.1" |
21 | |
22 | # Requiered to configure the netmask. |
23 | #NETMASK="255.255.255.0" |
24 | |
25 | # Required to configure the broadcast address. |
26 | #BROADCAST="192.168.0.255" |
27 | |
28 | |
29 | |
30 | |
31 | # Dynamic networking configuration example: |
32 | # This method may be used to obtain an address via DHCP. |
33 | |
34 | # Enables the dhcp networking method. |
35 | NETWORKING="dhcp" |
36 | |
37 | # Which dhcp client do you want to use ? |
38 | DHCP_PROG="/sbin/dhcpcd" |
39 | |
40 | # DHCP_START allows you to pass additional |
41 | # startup parameters to your dhcp client. |
42 | # Ex: Timeout after 10 seconds |
43 | DHCP_START="-t 10" |
44 | |
45 | # DHCP_STOP allows you to pass additional |
46 | # stop parameters to your dhcp client. |
47 | # Ex: -k kills the dhcp-cache at system shutdown |
48 | # -z will not; keeps the resolv.conf etc. |
49 | DHCP_STOP="-k" |
50 | |
51 | |
52 | |
53 | |
54 | # The GATEWAY variable should contain the default gateway IP address, |
55 | # if one is present. If not, then comment out the variables entirely. |
56 | #GATEWAY="192.168.0.100" |
57 | |
58 | |
59 | # The NAMESERVER variable should contain a list of DNS-servers, |
60 | # if there are some present. This also overrides the DHCP-settings. |
61 | #NAMESERVER="192.168.0.100 192.168.0.101" |
62 | |
63 | |
64 | # |
65 | # Wireless networking extensions (see man iwconfig(8) for more details) |
66 | # |
67 | # transfer rate 11M, 54M |
68 | #WIRELESS_BITRATE |
69 | # which channel shall be used [1-14] (use this or frequency) |
70 | #WIRELESS_CHANNEL |
71 | # network SSID |
72 | #WIRELESS_ESSID |
73 | # wich freqency shall be used |
74 | #WIRELESS_FREQUENCY |
75 | # wireless operation mode (managed=infrastrukte, ad-hoc, master=ap) |
76 | #WIRELESS_MODE |
77 | # nickname of the wireless node |
78 | #WIRELESS_NICK |
79 | # which authentification mode shall be used (wep,wpa,off) |
80 | #WIRELESS_AUTH_MODE |
81 | # Encryption key length, 64=WEP64, 128=WEP128, 256=WEP256 |
82 | #WIRELESS_KEY_LENGTH |
83 | # Encryption key in hex (or use ascii key) |
84 | #WIRELESS_KEY |
85 | # Encryption key in ascii (or use hex key) |
86 | #WIRELESS_KEY_ASCII |
87 | # driver used for wpa_supplicant |
88 | # WIRELESS_WPA_DRIVER=zydas |
89 | |
90 | |
91 | # |
92 | # Setup Bridges |
93 | # |
94 | # Note: to setup a bridge this file must be called net.br[0-9] |
95 | # |
96 | # Interface to which the bridge shall point to |
97 | #BRIDGE_INTERFACE="eth0" |
98 | # Here comes the same settings like with normal NICs |
99 | # A static example: |
100 | #NETWORKING="static" |
101 | #IP="192.168.0.1" |
102 | #NETMASK="255.255.255.0" |
103 | #BROADCAST="192.168.0.255" |
Properties
Name | Value |
---|---|
svn:executable | * |