1 |
# /etc/conf.d/net.eth0 - example eth0 network device configuration |
# /etc/conf.d/net.eth0 - example eth0 network device configuration |
2 |
# $Header: /home/cvsd/magellan-cvs/magellan-src/magellan-initscripts/etc/conf.d/net.sample,v 1.1 2007-09-30 10:36:10 niro Exp $ |
# $Header: /home/cvsd/magellan-cvs/magellan-src/magellan-initscripts/etc/conf.d/net.sample,v 1.2 2007-12-13 12:05:38 niro Exp $ |
3 |
|
|
4 |
# Enable this device automatically on system boot. |
# Enable this device automatically on system boot. |
5 |
# If set to anything but ?yes? the NIC will be ignored by |
# If set to anything but ?yes? the NIC will be ignored by |
72 |
#WIRELESS_ESSID |
#WIRELESS_ESSID |
73 |
# wich freqency shall be used |
# wich freqency shall be used |
74 |
#WIRELESS_FREQUENCY |
#WIRELESS_FREQUENCY |
75 |
# wireless operation mode (managed=infrastrukte, ad-hoc, master=ap) |
# wireless operation mode (managed=infrastructe, ad-hoc, master=ap) |
76 |
#WIRELESS_MODE |
#WIRELESS_MODE |
77 |
# nickname of the wireless node |
# nickname of the wireless node |
78 |
#WIRELESS_NICK |
#WIRELESS_NICK |
79 |
# which authentification mode shall be used (wep,wpa,off) |
# which authentification mode shall be used (wep,wpa,wpa2,off) |
80 |
#WIRELESS_AUTH_MODE |
#WIRELESS_AUTH_MODE |
81 |
# Encryption key length, 64=WEP64, 128=WEP128, 256=WEP256 |
# Encryption key length, 64=WEP64, 128=WEP128, 256=WEP256 |
82 |
#WIRELESS_KEY_LENGTH |
#WIRELESS_KEY_LENGTH |
83 |
# Encryption key in hex (or use ascii key) |
# Encryption key in hex (or use ascii key, WEP only) |
84 |
#WIRELESS_KEY |
#WIRELESS_KEY |
85 |
# Encryption key in ascii (or use hex key) |
# Encryption key in ascii (or use hex key, for WEP+WPA) |
86 |
#WIRELESS_KEY_ASCII |
#WIRELESS_KEY_ASCII |
87 |
# driver used for wpa_supplicant |
# driver used for wpa_supplicant (scripts defaults to wext) |
88 |
# WIRELESS_WPA_DRIVER=zydas |
# to see all possible drivers, run 'wpa_supplicant --help' |
89 |
|
#WIRELESS_WPA_DRIVER=wext |
90 |
|
|
91 |
|
|
92 |
# |
# |
94 |
# |
# |
95 |
# Note: to setup a bridge this file must be called net.br[0-9] |
# Note: to setup a bridge this file must be called net.br[0-9] |
96 |
# |
# |
97 |
# Interface to which the bridge shall point to |
# Interfaces to which the bridge shall point to |
98 |
#BRIDGE_INTERFACE="eth0" |
# It is possible to use more than one |
99 |
# Here comes the same settings like with normal NICs |
#BRIDGE_INTERFACES="eth0 eth1" |
100 |
|
# Enables or disables Spanning Tree |
101 |
|
# Possible values are 'on' and 'off' |
102 |
|
#BRIDGE_STP="on" |
103 |
|
# |
104 |
|
# Networking for the bridge can be configured as normal |
105 |
# A static example: |
# A static example: |
106 |
#NETWORKING="static" |
#NETWORKING="static" |
107 |
#IP="192.168.0.1" |
#IP="192.168.0.1" |