etc/conf.d/net.sample

# /etc/conf.d/net.eth0 - example eth0 network device configuration
# $Header: /home/cvsd/magellan-cvs/magellan-src/magellan-initscripts/etc/conf.d/net.sample,v 1.2 2007-12-13 12:05:38 niro Exp $

# Enable this device automatically on system boot.
# If set to anything but ?yes? the NIC will be ignored by
# the network script and not be brought up.
ONBOOT="no"


# Static networking configuration example:
# This method may be used to define ethernet interfaces with
# statically allocated IPv4 addresses.

# NETWORKING defines which method is used [static|dhcp].
#NETWORKING="static"

# IP is required to set the address of the interface.
#IP="192.168.0.1"

# Requiered to configure the netmask.
#NETMASK="255.255.255.0"

# Required to configure the broadcast address.
#BROADCAST="192.168.0.255"


# Dynamic networking configuration example:
# This method may be used to obtain an address via DHCP.

# Enables the dhcp networking method.
NETWORKING="dhcp"

# Which dhcp client do you want to use ?
DHCP_PROG="/sbin/dhcpcd"

# DHCP_START allows you to pass additional
# startup parameters to your dhcp client.
# Ex: Timeout after 10 seconds
DHCP_START="-t 10"

# DHCP_STOP allows you to pass additional
# stop parameters to your dhcp client.
# Ex: -k kills the dhcp-cache at system shutdown
#     -z will not; keeps the resolv.conf etc.
DHCP_STOP="-k"


# The GATEWAY variable should contain the default gateway IP address,
# if one is present. If not, then comment out the variables entirely.
#GATEWAY="192.168.0.100"


# The NAMESERVER variable should contain a list of DNS-servers,
# if there are some present. This also overrides the DHCP-settings.
#NAMESERVER="192.168.0.100 192.168.0.101"


#
# Wireless networking extensions (see man iwconfig(8) for more details)
#
# transfer rate 11M, 54M
#WIRELESS_BITRATE
# which channel shall be used [1-14] (use this or frequency)
#WIRELESS_CHANNEL
# network SSID
#WIRELESS_ESSID
# wich freqency shall be used
#WIRELESS_FREQUENCY
# wireless operation mode (managed=infrastructe, ad-hoc, master=ap)
#WIRELESS_MODE
# nickname of the wireless node
#WIRELESS_NICK
# which authentification mode shall be used (wep,wpa,off)
#WIRELESS_AUTH_MODE
# Encryption key length, 64=WEP64, 128=WEP128, 256=WEP256
#WIRELESS_KEY_LENGTH
# Encryption key in hex (or use ascii key)
#WIRELESS_KEY
# Encryption key in ascii (or use hex key)
#WIRELESS_KEY_ASCII
# driver used for wpa_supplicant
#WIRELESS_WPA_DRIVER=zydas


#
# Setup Bridges
#
# Note: to setup a bridge this file must be called net.br[0-9]
#
# Interfaces to which the bridge shall point to
# It is possible to give more then on
#BRIDGE_INTERFACES="eth0 eth1"
# Enables or disables Spanning Tree
# Possible values are 'on' and 'off'
#BRIDGE_STP="on"
#
# Here comes the same settings like with normal NICs
# A static example:
#NETWORKING="static"
#IP="192.168.0.1"
#NETMASK="255.255.255.0"
#BROADCAST="192.168.0.255"
1	# /etc/conf.d/net.eth0 - example eth0 network device configuration
2	# $Header: /home/cvsd/magellan-cvs/magellan-src/magellan-initscripts/etc/conf.d/net.sample,v 1.2 2007-12-13 12:05:38 niro Exp $
3
4	# Enable this device automatically on system boot.
5	# If set to anything but ?yes? the NIC will be ignored by
6	# the network script and not be brought up.
7	ONBOOT="no"
8
9
10
11
12	# Static networking configuration example:
13	# This method may be used to define ethernet interfaces with
14	# statically allocated IPv4 addresses.
15
16	# NETWORKING defines which method is used [static\|dhcp].
17	#NETWORKING="static"
18
19	# IP is required to set the address of the interface.
20	#IP="192.168.0.1"
21
22	# Requiered to configure the netmask.
23	#NETMASK="255.255.255.0"
24
25	# Required to configure the broadcast address.
26	#BROADCAST="192.168.0.255"
27
28
29
30
31	# Dynamic networking configuration example:
32	# This method may be used to obtain an address via DHCP.
33
34	# Enables the dhcp networking method.
35	NETWORKING="dhcp"
36
37	# Which dhcp client do you want to use ?
38	DHCP_PROG="/sbin/dhcpcd"
39
40	# DHCP_START allows you to pass additional
41	# startup parameters to your dhcp client.
42	# Ex: Timeout after 10 seconds
43	DHCP_START="-t 10"
44
45	# DHCP_STOP allows you to pass additional
46	# stop parameters to your dhcp client.
47	# Ex: -k kills the dhcp-cache at system shutdown
48	# -z will not; keeps the resolv.conf etc.
49	DHCP_STOP="-k"
50
51
52
53
54	# The GATEWAY variable should contain the default gateway IP address,
55	# if one is present. If not, then comment out the variables entirely.
56	#GATEWAY="192.168.0.100"
57
58
59	# The NAMESERVER variable should contain a list of DNS-servers,
60	# if there are some present. This also overrides the DHCP-settings.
61	#NAMESERVER="192.168.0.100 192.168.0.101"
62
63
64	#
65	# Wireless networking extensions (see man iwconfig(8) for more details)
66	#
67	# transfer rate 11M, 54M
68	#WIRELESS_BITRATE
69	# which channel shall be used [1-14] (use this or frequency)
70	#WIRELESS_CHANNEL
71	# network SSID
72	#WIRELESS_ESSID
73	# wich freqency shall be used
74	#WIRELESS_FREQUENCY
75	# wireless operation mode (managed=infrastructe, ad-hoc, master=ap)
76	#WIRELESS_MODE
77	# nickname of the wireless node
78	#WIRELESS_NICK
79	# which authentification mode shall be used (wep,wpa,off)
80	#WIRELESS_AUTH_MODE
81	# Encryption key length, 64=WEP64, 128=WEP128, 256=WEP256
82	#WIRELESS_KEY_LENGTH
83	# Encryption key in hex (or use ascii key)
84	#WIRELESS_KEY
85	# Encryption key in ascii (or use hex key)
86	#WIRELESS_KEY_ASCII
87	# driver used for wpa_supplicant
88	#WIRELESS_WPA_DRIVER=zydas
89
90
91	#
92	# Setup Bridges
93	#
94	# Note: to setup a bridge this file must be called net.br[0-9]
95	#
96	# Interfaces to which the bridge shall point to
97	# It is possible to give more then on
98	#BRIDGE_INTERFACES="eth0 eth1"
99	# Enables or disables Spanning Tree
100	# Possible values are 'on' and 'off'
101	#BRIDGE_STP="on"
102	#
103	# Here comes the same settings like with normal NICs
104	# A static example:
105	#NETWORKING="static"
106	#IP="192.168.0.1"
107	#NETMASK="255.255.255.0"
108	#BROADCAST="192.168.0.255"