Annotation of /trunk/rp-pppoe/dsl-provider

# $Header: /root/magellan-cvs/src/rp-pppoe/dsl-provider,v 1.1 2007-08-19 02:33:51 niro Exp $
#
# Configuration file for PPP, using PPP over Ethernet 
# to connect to a DSL provider.
#
# See the manual page pppd(8) for information on all the options.

##
# Section 1
#
# Stuff to configure...

# MUST CHANGE: Uncomment the following line, replacing the user@provider.net
# by the DSL user name given to your by your DSL provider.
# (There should be a matching entry in /etc/ppp/pap-secrets with the password.)
#user myusername@myprovider.net

# Use the pppoe program to send the ppp packets over the Ethernet link
# This line should work fine if this computer is the only one accessing
# the Internet through this DSL connection. This is the right line to use
# for most people.
pty "/usr/sbin/pppoe -I eth0 -T 80 -m 1452"

# An even more conservative version of the previous line, if things
# don't work using -m 1452... 
#pty "/usr/sbin/pppoe -I eth0 -T 80 -m 1412"

# If the computer connected to the Internet using pppoe is not being used
# by other computers as a gateway to the Internet, you can try the following
# line instead, for a small gain in speed:
#pty "/usr/sbin/pppoe -I eth0 -T 80"


# The following two options should work fine for most DSL users.

# Assumes that your IP address is allocated dynamically
# by your DSL provider...
noipdefault
# Try to get the name server addresses from the ISP.
usepeerdns
# Use this connection as the default route.
# Comment out if you already have the correct default route installed.
defaultroute

##
# Section 2
#
# Uncomment if your DSL provider charges by minute connected
# and you want to use demand-dialing. 
#
# Disconnect after 300 seconds (5 minutes) of idle time.

#demand
#idle 300

##
# Section 3
#
# You shouldn't need to change these options...

hide-password
lcp-echo-interval 20
lcp-echo-failure 3
# Override any connect script that may have been set in /etc/ppp/options.
connect /bin/true
noauth
persist
mtu 1492

# RFC 2516, paragraph 7 mandates that the following options MUST NOT be
# requested and MUST be rejected if requested by the peer:
# Address-and-Control-Field-Compression (ACFC)
noaccomp
# Asynchronous-Control-Character-Map (ACCM)
default-asyncmap

1	niro	306	# $Header: /root/magellan-cvs/src/rp-pppoe/dsl-provider,v 1.1 2007-08-19 02:33:51 niro Exp $
2			#
3			# Configuration file for PPP, using PPP over Ethernet
4			# to connect to a DSL provider.
5			#
6			# See the manual page pppd(8) for information on all the options.
7
8			##
9			# Section 1
10			#
11			# Stuff to configure...
12
13			# MUST CHANGE: Uncomment the following line, replacing the user@provider.net
14			# by the DSL user name given to your by your DSL provider.
15			# (There should be a matching entry in /etc/ppp/pap-secrets with the password.)
16			#user myusername@myprovider.net
17
18			# Use the pppoe program to send the ppp packets over the Ethernet link
19			# This line should work fine if this computer is the only one accessing
20			# the Internet through this DSL connection. This is the right line to use
21			# for most people.
22			pty "/usr/sbin/pppoe -I eth0 -T 80 -m 1452"
23
24			# An even more conservative version of the previous line, if things
25			# don't work using -m 1452...
26			#pty "/usr/sbin/pppoe -I eth0 -T 80 -m 1412"
27
28			# If the computer connected to the Internet using pppoe is not being used
29			# by other computers as a gateway to the Internet, you can try the following
30			# line instead, for a small gain in speed:
31			#pty "/usr/sbin/pppoe -I eth0 -T 80"
32
33
34			# The following two options should work fine for most DSL users.
35
36			# Assumes that your IP address is allocated dynamically
37			# by your DSL provider...
38			noipdefault
39			# Try to get the name server addresses from the ISP.
40			usepeerdns
41			# Use this connection as the default route.
42			# Comment out if you already have the correct default route installed.
43			defaultroute
44
45			##
46			# Section 2
47			#
48			# Uncomment if your DSL provider charges by minute connected
49			# and you want to use demand-dialing.
50			#
51			# Disconnect after 300 seconds (5 minutes) of idle time.
52
53			#demand
54			#idle 300
55
56			##
57			# Section 3
58			#
59			# You shouldn't need to change these options...
60
61			hide-password
62			lcp-echo-interval 20
63			lcp-echo-failure 3
64			# Override any connect script that may have been set in /etc/ppp/options.
65			connect /bin/true
66			noauth
67			persist
68			mtu 1492
69
70			# RFC 2516, paragraph 7 mandates that the following options MUST NOT be
71			# requested and MUST be rejected if requested by the peer:
72			# Address-and-Control-Field-Compression (ACFC)
73			noaccomp
74			# Asynchronous-Control-Character-Map (ACCM)
75			default-asyncmap
76